Perfect Union banner
1 - 15 of 15 Posts

·
Registered
Joined
·
2,003 Posts
Discussion Starter · #1 ·
It was way overdue for a complete revamp. Check out the new digs if you have a moment, and let me know what you think. It's still being tweaked, so you may notice some formatting issues.

www.accu-strut.com
 

·
Registered
Joined
·
10,469 Posts
Nice job!
 
  • Like
Reactions: RJF

·
Registered
Joined
·
9 Posts
Man, this site is still looking great, despite the fact that it is kind of outdated, and you haven't made any single update to it in ages. Are you still maintaining it?! I mean, it took me a while to find the website, on the search engines, mostly it is on the 5th page, so you really have to improve the serch engine optimization, as your website is going to die soon! If you do not know any great seo specialists, you might call for the services of https://www.pixelchefs.com/ecommerce-website-design/, as they are probably the best in seo and ecommerce website design as well.
 

·
Formerly "raf"
Joined
·
2,523 Posts
It was way overdue for a complete revamp. Check out the new digs if you have a moment, and let me know what you think. It's still being tweaked, so you may notice some formatting issues.

www.accu-strut.com
Tool a quick look around. Seems fine.

Some suggestions:
1) Make sure the buyers of single-clamp struts are made aware that such struts are not nearly as effective as dual-clamp struts.

2) Is the end-cap on the typical strut removable? I have a "Drilled" dual clamp strut, so if removing the end-cap of the "Standard" strut is a possibility, (and accessing some storage room within the strut a possibility), then state so, either way.

3) Educate possible buyers why your device is the best available, without directly attacking other mfrs. Just state the facts, without attacks, and let the buyer decide.

All best wishes!
 

·
Registered
Joined
·
2 Posts
Man, this site is still looking great, despite the fact that it is kind of outdated, and you haven't made any single update to it in ages. Are you still maintaining it?! I mean, it took me a while to find the website, on the search engines, mostly it is on the 5th page, so you really have to improve the serch engine optimization, as your website is going to die soon! If you do not know any great seo specialists, you might call for the services of https://www.pixelchefs.com/ecommerce-website-design/, as they are probably the best in seo and ecommerce website design as well.
Why didn't I know about this before.This is a really good solution)
 

·
Registered
Joined
·
2,003 Posts
Discussion Starter · #9 ·
Thank you very much for all your comments. Sorry, been travelling the past week and just got back. Yes, the website is due for some more fine-tuning, and I'll seriously consider some of your suggestions.

I've been a bit pre-occupied with medical issues (had a congestive heart failure last October), but I'm more-or-less back in the fold now.
 

·
Registered
Joined
·
101 Posts
Thank you very much for all your comments. Sorry, been travelling the past week and just got back. Yes, the website is due for some more fine-tuning, and I'll seriously consider some of your suggestions.

I've been a bit pre-occupied with medical issues (had a congestive heart failure last October), but I'm more-or-less back in the fold now.
KKINA, Slow down and take things as they come, and above all, pay attention to "doctor's orders". The weapons community need innovative folks like yourself, so stay with us and stay safe.
Thanks, Gary
 

·
Registered
Joined
·
2,003 Posts
Discussion Starter · #12 ·
I did some minor revamping of the site today.

On the relative effectiveness of single- vs. double-clamp, that issue is already addressed in our FAQ section. Maybe there's a way to make it more pronounced?

As far as the removable end-cap, I'm actually hesistant to promote the strut as a spare storage area. I have no control over things that might be put in there, and how it might affect performance (or even be dangerous). I prefer to keep things a little vague, to tell the truth.

I've played up the superiority of our system a bit, especially the flex-clamp design. I actually have seen incidents where the block clamps of our competitors have reduced accuracy, sometimes dramatically.

Deleted a few missing videos.

Anyways, keep those great suggestions coming, and I'll try to keep the site current.
 

·
Registered
Joined
·
631 Posts
Looks better.
Two suggestions:
Better quality photos.
And why not sell direct and cut out the middle man, I am thinking this could bring the price down a bit.
By the way, Love the XDrill model, works great on the skinny and the tapper barrel.
I recommend the Accustrut to all my customers buying a Mini, and there have been a lot.
 

·
Been here forever.....
Joined
·
221 Posts
Would you consider selling just a few sets of clamps? Would be a heck of a nice light mount for a mini mag. Could even machine a new tailcap to clamp around the gas block...
 
1 - 15 of 15 Posts
Top