[gunrunner12]

Hi
where can I receive a 5rd magazine from, for the Norinco 86 / .223

2 if we can buy them, what's the cost?

thanks

 

[Flak 2]

gunrunner I'm not sure on the 5 rounders. Theres the Bulgarian poly 10 rnd that should work in your 223 Norinco. I'll keep an eye out, but can't remember seeing any. You could pull the base plate and make a wood plug and stuff up there to limit a 10 to 5rnds. most state hunting laws will allow you to put a plug in the mag. You could also pop rivet stops on a 10 like Canadians.

 

[gunrunner12]

Hi Flak 2

I need to get the magazine down to say maximum 7 rounds & the mag can not look like a big mag, so I'm thinking about the mini 14 mag that maybe able to be modified?

Can the mini 14 be modified? I do not know this one, but may as around.

thanks Flack

 

[Flak 2]

gunrunner i suppose a Mini mag could be made to work. I think it would take quite a bit of work though. There a guys that use the East German bakelites in the 223 Norincos. The bakelites can be cut down and epoxied back together. It would be like taking 6 inches out of the center of the magazine then epoxian the upper and lower halfs together. I've cut down a few for bench work for the SAR3. They ended up at 14 and 17rnds. I don't think you'll be able to shortin an AK MAG enough to be flush with the bottom of the reciever though. There'd be at least 2 inches of the magazine showing. The 10rnd factory mags leave about 3 inches of magazine exposed. gunrunner why are you worried about blocking a 10rnd. to 5?

 

[gunrunner12]

Hi Flak 2

Why I want to limit the magazine, well the law for "A" license, is that there can not be more than 7rds in the magazine.

I want to put the rifle under the "A" because there are less rules, under military "E" if restricted rifle, harder all round to go out & have fun hunting ect

 

[Flak 2]

is it legal to plug or rivet a stop plate in a 10rnd. If thats not acceptable I'd go the bakelite route and section a couple. The bakelites can be had for $5.00ea for the 30rnd. Unless you have to have a special license to buy hi caps where your at. If thats the case I'd shorten a spring and rivet a limiting device like bent sheet metal inside your mag. Good luck

 

[gunrunner12]

Hi Flak 2

Bulgarian poly magazines, where can I purchase them from?

Are they cheap? I guess the ploy is plastic?

They "law" does not allow 7 round mags or less to look like a banana magazine, because people thing it's begger than it really is.

There must be away, to reduce the 10rd mags, we could limit within the mag itself, so the 10 round would be a great mag, it does not look much bigger than the 7rd anyway.

Searching the internet now, to try & find some. Do you have any in your area " State "?

thanks

to your question:
is it legal to plug or rivet a stop plate in a 10rnd.

I think this would be ok, within the law

 

[gunrunner12]

Hi Flak 2

so far I have found only a Bulgarian 14rd magazine

Still searching

 

[Flak 2]

Bottom left side of page. heres the link try these guys K-VAR Corp. http://www.k-varcorp.com/magazines.html

 

[gunrunner12]

Flak 2

thanks for this help, there is a 5rd on this page, great .

So this mag M-74N5 ~ Bulgarian 5 Rd, This will click into the normal AK 47 // .223 version?

if so then I will order one

thanks

Question: this website http://www.k-varcorp.com/

it says if I'm a forum member I can buy it for $12.99 how can I be a member? K-Var Price 12.99 or 22.00 MSRP

thanks

 

[gunrunner12]

I have joined the forum, to get the mag cheaper.

http://kalashnikov.guns.ru/wwwboard/board1/index.html

if you are a member, then the mag is $12.99 american.

Will wait until they email me, for my membership details, then I will order the mag,

thanks