Ruger Mini-14 and Mini-30 Ruger Mini-14 and Mini-30 family of rifles

Reply
 
LinkBack Thread Tools Display Modes
Old 06-14-2012, 07:32   #1
Full Member
Points: 3,702, Level: 38 Points: 3,702, Level: 38 Points: 3,702, Level: 38
Activity: 1.2% Activity: 1.2% Activity: 1.2%
Last Achievements
 
milspecnsn's Avatar
 
Join Date: Nov 2010
Location: Virginia
Posts: 57
What height/model# Warne QD rings for Redfield Scope

Hi,


I'm planning on a Redfield Revolution 2-7X scope on my Mini Ranch. I intend on leaving the rear sight on so I'm assuming the medium height rings?

What's the correct Warne model # to fit the Ruger receiver's scallops?

Thanks in advance

John
milspecnsn is offline   Reply With Quote
Old 06-14-2012, 07:53   #2
Full Member
Points: 13,816, Level: 76 Points: 13,816, Level: 76 Points: 13,816, Level: 76
Activity: 13.4% Activity: 13.4% Activity: 13.4%
Last Achievements
 
Join Date: Feb 2010
Location: Atlanta Suburbs
Posts: 457
Be 1RLM for 1" or 14RLM for 30mm
I have had 3 sets of them - all med high on two Mini's. The only issue I've had with clearance is with some scopes with 42mm objective end, the bell clearance is too close for the hand-guard. And I am talking about a small amount. The Mark AR 4-12 x 42 on my Mini-14 Target was one which needed just a little extra clearance. In a lot of those cases, you can file or dremel some of the top of the hand-guard off for the clearance. And the hard plastic kind of polishes up after and really doesn't look bad. The hand-guard is a cheap replaceable plastic part available from multiple sources for $15 - $20 in case you want to take it back to stock after.

Last edited by myname; 06-14-2012 at 07:54. Reason: typo
myname is offline   Reply With Quote
Old 06-14-2012, 08:03   #3
Full Member
Points: 1,466, Level: 21 Points: 1,466, Level: 21 Points: 1,466, Level: 21
Activity: 17.4% Activity: 17.4% Activity: 17.4%
Last Achievements
 
Join Date: Feb 2012
Posts: 204
I believe the ones youll want are the 1RLM. Theyre slightly lower than the stock Ruger high rings.
breckenridge is offline   Reply With Quote
Old 06-14-2012, 14:53   #4
Full Member
Points: 3,289, Level: 35 Points: 3,289, Level: 35 Points: 3,289, Level: 35
Activity: 0% Activity: 0% Activity: 0%
Last Achievements
 
Join Date: May 2010
Location: SF North Bay
Posts: 116
These are the ones you want for the 1" tubed Redfield:
WARNE RUGER #1 Quick Detach, Blackhawk & Mini 14 Rings, 1in., Medium, Matte (1RLM)
P220forever is offline   Reply With Quote
Old 06-14-2012, 17:46   #5
Full Member
Points: 3,702, Level: 38 Points: 3,702, Level: 38 Points: 3,702, Level: 38
Activity: 1.2% Activity: 1.2% Activity: 1.2%
Last Achievements
 
milspecnsn's Avatar
 
Join Date: Nov 2010
Location: Virginia
Posts: 57
Thank you gentlemen. Exactly what I needed to know. I've swapped the stock handguard for a Choate.

Regards

John
milspecnsn is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 11:35.
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Friendly URLs by vBSEO 3.6.1
All information is copyright by Perfectunion.com unless already under copyright.

This site is Gunny Approved